8 Cylinder Propane Injection Kit, 300+ HP [8cyl300] | DudaDiesel Biodiesel Supplies
Home Page > 8 Cylinder Propane Injection Kit, 300+ HP [8cyl300]
Search Store

8 Cylinder Propane Injection Kit, 300+ HP

• For Sequential / Multi-Point Fuel Injected Vehicles

• Dual Fuel System (Switch Between Gasoline and Propane)

• Includes Software and USB Interface Cable for Automatic Calibration & Programming, 1 Year Warranty on Parts

Quantity
Price Each:
1+
1,399
Out of stock
Currently Unavailable
Item Pictures
8 cylinder 300+ HP propane LPG kit 8 cylinder 300+ HP propane LPG kit
propane kit 8 cylinder over 300 HP propane kit 8 cylinder over 300 HP

Item Description

SGI LPG System

Sequential / Multi-Point Gas Injection System

Maxi Kit

Catalog for LPG / Propane Kits
4 Cylinder (<300 HP)
6 Cylinder (<300 HP)
8 Cylinder (<300 HP)
8 Cylinder (>300 HP)
Installation Photos (zipped)

A Note on Maximum Power

Maximum powers given on the kits are based on the amount of fuel flow in which the reducer(s) can handle. The injectors can handle a maximum of 60 HP per cylinder. So in an ideal installation, an 8 cylinder vehicle can handle a maximum of 480 HP, and a 10 cylinder vehicle a maximum of 600 HP etc.. In a practical sense, the maximum HP cannot be obtained in an installation because of additional pressure losses due to from lengths of fuel lines used. Although this is mostly a problem for very high power vehicles using the 300+ HP kit, fuel lines should be made as short as possible to achieve the highest efficiency in any system installation.

 

Propane Fuel Injection for Electronically Controlled Fuel Injected Vehicles

Not for carburated engines. Complications may occur with multi-valve throttle body engines such as BMW valvetronic and BMW M-series engines.

 

This kit includes everything needed to successfully convert your vehicle to propane except for the tank and any filler valves involved with the tank. Kit includes all parts and USB connections for laptop, software, full instructions with wiring diagrams and full automated calibration for easy setup.

SGI ECU VERSUS
Gas injection controller is the IV generation device fulfilling rigorous standards regarding fuel dosage and performance quality. Constructor's team has worked out control algorithms of LPG injectors based on control signals of gasoline fuel injectors where real- time corrections are calculated for every injector separately. Thanks to it is needless to prepare the map of LPG injectors (as it was in older constructions of controllers) and to use OBD emulators.
A great advantage of the controller VERSUS is the possibility of mapping of LPG injectors expenses
towards gasoline fuel injectors during calibration drive, which simplifies and shortens the time of device installation in a car and respectively raises the quality of control and reduces fuel consumption. It increases versatility of the controller assembling and calibration processes are irrespective of type and brand of a car as well as of used mechanical components (reducers, injectors). It is possible for assemblers, who are accustomed to older generations of devices to calibrate controller in a traditional way by manual modifying the composition of mixture.

Advantages of ECU VERSUS:
Supply of the LPG-AIR mixture to the cylinders in the optimal phase of the engine cycle - corresponding with
the cycle used by the injection of gasoline
Simplicity in service, configuration and diagnostics of the system
Compatibility with EOBD
The system can be adapted to fit engines with Sequential, Half-sequential and non sequential Injection system.
The system can be fitted to Turbo-charged engines
Properly calibrated system allows to get the same driving dynamic on LPG as on Gasoline
Sophisticated software. "Creating map" allows precise calibration of the engine supplying with LPG
Diagnostic/assistance tools in the software
Environment friendly - complies with exhaust emission standards EURO 2, EURO 3, EURO 4
Clear, simple, user friendly interface allowing for time efficient service.
Fully automatic operation including automated switching from LPG to petrol when the LPG tank is empty
Eliminates Backfire and possible consequential damage of intake manifolds, air filters and housing or flow
meters
Availability for 3,4,5,6,8 - cylinder Engines.

 

This propane injection system is added to the existing gasoline fuel system of your vehicle by adding injectors for propane to the intake manifold and using an advanced Electronic control unit to manage the propane injection. The existing gasoline system is used for cold startup and the system switches to propane when warm enough for heating the liquid propane to make it into a gas. When propane runs out, the system switches back to gasoline. This is a dual fuel system.

 

This kit is programmable to any fuel injected vehicle and will work with any vehicle up to 300hp using the included super reducer. If your vehicle requires a higher power kit, you will need 2 reducers. The only requirement is to match the amount of cylinders in the system. Installation is fairly simple and can be done in about 1-2 days, depending on mechanical working skills. Most mechanics should be able to install this kit for anyone who does not have the time or basic mechanical skills for installation.

 

Fuel Economy:

Gasoline and liquid propane are not the same in energy density, so it is like comparing apples to oranges when comparing the fuel economy of propane versus gasoline. However, to put a number out there, there is roughly a 10% loss in fuel economy when comparing gallons to gallons of both fuels. Propane burns much more efficiently than gasoline, but it has much less energy density than gasoline. For this matter, check the current price of propane from a gas company you can fill up from versus the price of gasoline at the pump and then increase the price of the propane by 10% for an apples to apples comparison of which is more cost effective.

 

Installation is fairly simple. Anyone with some mechanical experience can install this kit in a day or 2. The ECU programming is done through software run on a laptop and a simple test run for calibration.

About the ECU:

The most visible advantage of VERSUS controller is that it is quite easy to install and than to tune it. That is mainly due to sophisticated algorithms inside processor as well as easy software. As a result ECU VERSUS can read many parameters of the engine by itself and finally set up proper value automatically.

ECU VERSUS is the IV generation high quality device fulfilling rigorous standards regarding fuel dosage and performance. Our design control algorithms of GAS injectors are based on control impulses for fuel injectors where real time corrections are calculated for every injector separately.


Another great advantage of VERSUS
is its ability to map GAS injectors' based on performance of gasoline fuel injectors during the drive. This simplifies and shortens the time of device installation in a car and respectively raises the quality of control and reduces fuel consumption.

Installation and calibration processes are universal and irrespective of the type and brand of a car, as well as the mechanical components uses (reducers, injectors). For installers, who are accustomed to older generations of devices it is still possible to calibrate ECU VERSUS in a traditional way by manual modifying the composition of mixture.

A miniature console is the only element of the system installed inside the drivers cabin. This small unit allows the driver to observe the level of GAS in the tank, indicates the stages of employment of the ECU, and allows for a manual change in the employment of the controller.

Calibration of ECU VERSUS:

  • The software used for the ECU Versus has an option for the calibration of the system under a full load during driving. This allows for performance nearly identical to gasoline. The installer is asked to set up basic settings. All complicated feeding application processes are under micro-controller responsibility inside ECU.

  • Additional functions allows for self-diagnostics of the system and correction of problems when necessary.

  • Possibility of manual modification of the composition of the mixture within the range of -25% to + 25% and time of injection 1-20 ms.

  • The program contains information important for future servicing and warranty issues related to the unit, such as the size of the engine, size of installed injectors and the date of the installation.

  • ECU Versus is extremely versatile so that it allows for various configuration of the components making it suitable to be used with almost any car on the market.

 

About the Kit:

:
ECU VERSUS (Electronic Control Unit) has been designed based on the most
recent methods of processing electronic impulses
in CNG/LPG dosage systems.
Main features of ECU VERSUS:
- Efficient processor that supports automatic recognition of engine parameters
- Clear, simple, user friendly interface allowing for time efficient service.
- The software used for the ECU Versus has an option for the calibration of the
system under a full load during driving. This allows for performance nearly
identical to gasoline. All complicated feeding application processes are under
micro-controller responsibility.
- Simplicity in service, configuration and diagnostics of the system
- Environment friendly - complies with exhaust emission standards EURO 4
- Fully automatic operations including automated switching from GAS to
Gasoline when the tank is empty.
- Additional functions allow for self-diagnostics of the system and correction
of problems when necessary.
-ECU Versus is extremely versatile so that it allows for various configuration
of the components making it suitable to be used with almost any car on the
market.
ECU VERSUS has E67R-01 approval LPG and E110R approval CNG

ECU Components:

1. ECU

2. Harness with waterproof plugs.
3. Map-sensor. Different types available.
4. GAS Temperature sensor.
5. Reducer's temperature sensor.
6. Switch with horn signal.
7. Waterproof fuse box.

 

Propane Components

1. Super Reducer with its support and fittings. (Up to 300 HP)
2. Injectors with their accessories: Injectors support, Calibration nozzles and inlet manifold nozzles
3. Gas Filter (2 filters provided for 8 cylinder kit)
4. Level Indicator
5. Vacuum T-fitting connection

6. Additional Components

(Sizes of hoses will vary depending on the cylinders of the kit)

About the Reducer:

LPG VR-L "SUPER" Reducer:
We offer the new series of VR-L "SUPER" type of pressure regulators.
The latest VR-L "SUPER" reducer was designed to be used in the most
sophisticated engines taking into consideration their power efficiency.
It is supplied with advanced Liquid Phase Heating System. Due to that it
ensures stable pressure in spite of outside temperature.
The reducer can be installed in engines up to 220 KW power (300 hp). It is also
integrated with Coil Group Valve that so there is no need to install any
additional valve in the circuit.
VR-L

VR-L "SUPER" Technical Data:
Type of GAS: LPG
Body: Aluminum die cast
Liquid Gas Heating System "LGHS": supplied
Homologations: ECE 67R 01
Gas Outlet Pressure: 1,2 bar
Maximum Power: 220 kW (300 HP)
Working Temperature Range (0C): -30 /+120
Gas Outlet External Diameter: 14 mm
Gas Inlet: 8 mm
Engine Cooling liquid Outlet/Inlet: 16 mm
Shut-off Valve: integrated
Vacuum nozzle: Present
Solenoid Valve Nominal Voltage: 12V
Overall dimension: 135/190/130 mm
Body Diameter: 100 mm
Weight: 1,3 kg

 

 

Legal Notes: This kit is not EPA certified. Installations of this kit are intended for non-highway usage (offroading only). Duda Diesel is not responsible for violation of EPA regulations should this kit be used for other means.
 

Average Rating: 9.00/10

Write a review

Content on this page requires a newer version of Adobe Flash Player.

Get Adobe Flash player

Customer Reviews:
Customer: david canady
0000-00-00

Rating: 9/10
Pros: easy to install 2006 chevy pickup has 145,000 miles 50,000 with versus kit
Cons: some its hard to refuel when temp outside is near 100 deg
Other: None


© 2008 DudaDiesel.com | Biodiesel & Alternative Energy Supplies